Skip to content
No Second Trip

Costs

Soffit and fascia cost

What soffit and fascia cost per linear foot installed, by material, and what drives the price on a replacement job.

Updated

The underside of a newly fitted roof overhang showing clean vented soffit panels, a painted fascia board, and a new gutter.

Soffit and fascia replacement costs $6 to $20 per linear foot installed for both together. A typical house with a 150 foot perimeter runs $1,500 to $3,000, with vinyl soffit and aluminium-wrapped fascia landing near $10 per foot.

Because the work is priced by the foot and measured around the whole house, the perimeter is the number that drives everything. Measure it before you take quotes.

Soffit Calculator

Work out soffit panels, J- and F-channel and fascia from your eave run and overhang — and check the ventilation meets code before you order.

Full soffit calculator, with formulas and sources

Cost by material

Installed, per linear foot, including channel and fasteners.

MaterialSoffitFasciaTogether
Vinyl$3 – $7$4 – $8$6 – $14
Aluminium$4 – $9$5 – $10$8 – $18
Aluminium wrap over existing wood—$4 – $9—
Fibre cement$6 – $12$7 – $14$12 – $25
Wood (pine, painted)$5 – $10$6 – $12$10 – $20
Cedar or hardwood$9 – $18$10 – $22$18 – $38

Cost by house size

Both soffit and fascia, vinyl and wrapped aluminium, single storey.

House perimeterTypical sizeCost range
100 ftSmall ranch$800 – $1,800
150 ftTypical 3-bed$1,300 – $2,800
200 ftLarger, or with garage$1,700 – $3,800
300 ftLarge or complex roofline$2,500 – $5,500

Rot repair is the unknown

Soffit is usually replaced because water got in, which means the fascia board or the rafter tails behind it may be rotten. Nobody can price that before the old material comes off. Expect an allowance in the contract with a per-foot rate beyond it — a quote that promises no repairs will be needed has not looked.

What pushes the price up

Height. Two storeys means scaffolding or a lift, adding $300 to $1,000. This is the most common reason two quotes on the same house differ.

Rot behind the fascia. Replacing rafter tails is carpentry, not trim work, and it is billed accordingly — often $50 to $150 per tail.

Roofline complexity. Dormers, multiple gables, bay windows and porch returns all mean more corners, more cuts and more channel. A simple rectangle is much cheaper per foot than a cut-up roofline.

Overhang depth. A wide overhang needs more material per foot, and beyond 24 inches it also needs intermediate nailers to stop vinyl sagging.

Adding ventilation. If the existing soffit was solid and the attic is under-ventilated, switching to vented panels is close to free at this point — but adding baffles inside the attic so the insulation does not block the airflow is extra.

Doing it at the same time as the roof

If the roof is being replaced, do the soffit and fascia at the same time. The drip edge, the F-channel and the first course of shingles all meet at that joint, and doing them together avoids paying twice for access and avoids a compromised detail where new meets old.

It is also the only moment when the attic ventilation can be fixed properly from both ends — intake at the eave and exhaust at the ridge, matched.

Where the money is worth spending

Vented rather than solid soffit costs almost nothing extra and is the cheapest attic ventilation you will ever buy.

Aluminium rather than vinyl on a wide overhang, because vinyl sags in heat over about 24 inches and looks poor within a few summers.

Wrapping the fascia in aluminium rather than painting wood, if the wood is sound. It ends the repainting cycle for a fraction of full replacement.

Prices here are national US ranges for 2026 and are for planning only. Get at least two local quotes, and ask each to state their rot repair allowance separately.

Common questions

How much does it cost to replace soffit and fascia?

Between $6 and $20 per linear foot installed for both together, with vinyl soffit and aluminium-wrapped fascia near $10. A typical 150 foot perimeter runs $1,500 to $3,000.

Should soffit and fascia be replaced together?

Usually yes. They meet at the same joint, and the fascia has to come off to fit F-channel properly. Doing them separately means paying twice for the same access and scaffolding.

Does soffit and fascia work need scaffolding?

On a single storey, ladders are usually enough. On a two-storey house or where the ground is uneven, scaffolding or a lift adds $300 to $1,000 to the job and is a common reason quotes differ.

Calculators for this

  • Soffit Calculator

    Work out soffit panels, J- and F-channel and fascia from your eave run and overhang — and check the ventilation meets code before you order.

Part of our roofing guide.

Reviewed by Quban, Construction estimator, on . How these numbers are checked.