Asphalt Calculator
Asphalt is specified by thickness but sold by weight. Enter your dimensions and this works out the tonnage to order, using compacted in-place density rather than loose density — the figure your supplier bills against.
The formulas
Tonnage
Tons = (Area × Thickness × (1 + Waste)) × Density ÷ 2000
Area times compacted thickness gives the in-place volume. Multiplying by compacted density converts that volume to weight, and dividing by 2,000 lb converts to US tons. The waste factor is applied to volume, before the density conversion.
Area
Area = Length × Width
For an irregular drive, split it into rectangles, calculate each separately and add the tonnages. Do not average the width of a wedge-shaped area — that under-orders the wide end.
Why compacted density
Compacted density ≈ Loose density × 1.15 to 1.20
Asphalt arrives loose and is rolled to its final density. Suppliers quote tonnage against the compacted figure, which is why this calculator uses in-place density (about 145 lb/ft³ for standard HMA) rather than loose density.
Worked example
A standard two-car driveway
A 40 ft × 12 ft driveway (480 sq ft) surfaced with 2 in of standard hot-mix asphalt, with the default 5% waste allowance. Area × thickness gives 80 cu ft, which becomes 84 cu ft with waste. At 145 lb/ft³ that is 12,180 lb.
6.09 tons of asphalt
A metric equivalent
A 12 m × 3.7 m driveway at 50 mm compacted thickness, same mix and waste allowance. The calculation is identical — only the entry and display units change.
5.41 tonnes of asphalt
Typical asphalt thickness by use
Compacted thickness of the asphalt itself, over a separately compacted aggregate base. Local frost depth and soil conditions govern the real specification — check with your paver.
| Application | Surface course | Total asphalt | Aggregate base |
|---|---|---|---|
| Residential driveway | 2 in | 2–3 in | 4–6 in |
| Residential driveway, heavy vehicles | 2 in | 3–4 in | 6–8 in |
| Parking lot, cars only | 2 in | 3 in | 6 in |
| Parking lot, truck traffic | 2 in | 4–6 in | 8–12 in |
| Private road | 2 in | 4–5 in | 8–12 in |
| Footpath or cart path | 1.5–2 in | 1.5–2 in | 3–4 in |
Asphalt tonnage at a glance
Standard dense-graded surface mix at 145 lb/ft³ compacted, including a 5% waste allowance. Use these to sanity-check the calculator.
| Area | At 2 in | At 3 in | At 4 in |
|---|---|---|---|
| 100 sq ft | 1.27 tons | 1.90 tons | 2.54 tons |
| 250 sq ft | 3.17 tons | 4.76 tons | 6.34 tons |
| 500 sq ft | 6.34 tons | 9.52 tons | 12.69 tons |
| 1,000 sq ft | 12.69 tons | 19.03 tons | 25.38 tons |
| 2,500 sq ft | 31.72 tons | 47.58 tons | 63.44 tons |
| 5,000 sq ft | 63.44 tons | 95.16 tons | 126.88 tons |
Values used
Every number this calculator applies on your behalf is listed here, with its source. If your supplier quotes a different figure, use theirs — materials vary by region and grade.
| Value | Used | Typical range | Source |
|---|---|---|---|
| Surface course (standard HMA) density | 145 lb/ft³ | 142–148 | National Asphalt Pavement Association (NAPA) |
| Binder course density | 148 lb/ft³ | 145–152 | National Asphalt Pavement Association (NAPA) |
| Asphalt base course density | 150 lb/ft³ | 146–155 | National Asphalt Pavement Association (NAPA) |
| Porous / permeable asphalt density | 125 lb/ft³ | 118–133 | National Asphalt Pavement Association (NAPA) |
| Recycled asphalt (RAP) density | 138 lb/ft³ | 130–145 | National Asphalt Pavement Association (NAPA) |
| Default waste allowance | 5 % | 3–10 | — |
| Typical delivered price | 150 $ | 100–200 | Asphalt Institute |
- Porous / permeable asphalt density: Open-graded mixes carry 15–25% air voids, so they weigh materially less per cubic foot than dense-graded HMA.
- Default waste allowance: Covers edge spill, truck hold-back and thickness variation. Raise it for irregular shapes or a rough base.
- Typical delivered price: Per US ton, material delivered, before placement labour. Varies widely with oil prices and haul distance.
Common questions
How many tons of asphalt do I need for a 2-inch driveway?
At 2 in compacted thickness with standard hot-mix asphalt, plan on roughly 0.0127 tons per square foot including 5% waste — about 6.1 tons for a typical 40 ft × 12 ft driveway. Multiply your square footage by 0.0127 for a quick estimate, or use the calculator above for your exact dimensions and mix.
How thick should an asphalt driveway be?
A residential driveway normally uses 2–3 in of compacted asphalt over 4–6 in of compacted aggregate base. Go to 3–4 in of asphalt over 6–8 in of base if trucks or RVs will use it. In cold climates the base depth matters more than the asphalt depth, because frost heave is what breaks driveways.
What does a ton of asphalt cover?
One ton of standard hot-mix covers about 83 sq ft at 2 in thick, 55 sq ft at 3 in, or 41 sq ft at 4 in. That assumes 145 lb/ft³ compacted density; a porous mix covers roughly 15% more area per ton because it weighs less.
Should I order extra asphalt?
Yes — 5% is the standard allowance and the calculator applies it by default. Raise it to 8–10% for an irregular shape, a rough or uneven base, or a job with many edges and cutouts. Unlike gravel, leftover asphalt cannot be saved: it has to be placed hot.
Is asphalt sold by the ton or by the yard?
By the ton, in almost all of the United States. Volume is only used at the design stage. That is why this calculator converts your thickness specification into weight — the number the supplier actually quotes and bills against.
Does this include the gravel base?
No. This calculates the asphalt layer only. The aggregate base underneath is a separate material with a different density, usually 4–8 in deep — work that out with a gravel calculator and order it separately.
Keep going
Related calculators
- Gravel calculator
For the compacted aggregate base under the asphalt
Guides
- How much asphalt do I need?
The tonnage shortcut and why compacted density is the one that counts
- Asphalt vs concrete driveway
Cost, lifespan and climate trade-offs
Costs
- Asphalt driveway cost
Installed prices per square foot
Sources
- Hot Mix Asphalt Materials, Mixture Design and Construction — National Asphalt Pavement Association (NAPA)Compacted HMA density typically 142–148 lb/ft³ depending on aggregate and mix.
- MS-2 Asphalt Mix Design Methods, 7th edition — Asphalt InstituteSource for mix classification and typical in-place air voids.
- Pavement Design Guidance for Local Roads and Driveways — US Federal Highway AdministrationTypical residential driveway surface course 2–3 in over 4–8 in aggregate base.
- NIST Special Publication 811: Guide for the Use of the SI — US National Institute of Standards and TechnologyExact definitions of the inch, pound and US short ton used in conversions.
Reviewed by Quban, Construction estimator, on . How these numbers are checked.