Gravel Calculator
Gravel is sold by the cubic yard by some suppliers and by the ton by others, so this gives you both. Density varies a lot between aggregates — lava rock weighs less than half what crushed stone does — so pick your material rather than accepting an average.
The formulas
Volume
Cubic yards = (Area × Depth in feet) ÷ 27
Depth is almost always given in inches, so divide it by 12 first. There are 27 cubic feet in a cubic yard, which is why that number appears in every gravel calculation.
Weight
Tons = Cubic feet × Density ÷ 2000
Density is the whole game. Crushed stone runs about 100 lb/ft³, decomposed granite 110, and lava rock only 45. Using a generic figure can be 50% out on a decorative stone.
Compaction
Loose volume = Finished volume × Compaction factor
A compacted base loses about 20% of its loose volume when rolled. If your layer is going to be compacted, you must order that extra volume — otherwise the finished depth comes up short.
Worked example
A gravel driveway surface
A 30 ft × 12 ft driveway (360 sq ft) topped with 4 in of #57 crushed stone, with the default 10% waste allowance and no compaction. Area × depth gives 120 cu ft, which becomes 132 cu ft with waste — just under 5 cubic yards.
4.89 cubic yards
A compacted paver base
The same 360 sq ft at 4 in, but in crusher run that will be compacted. The 1.22 compaction factor means ordering about a fifth more material than the finished volume suggests.
5.96 cubic yards
Gravel coverage per cubic yard
How much ground one cubic yard covers at a given depth, before any waste allowance. Useful for checking a supplier quote quickly.
| Depth | Coverage per cu yd | Typical use |
|---|---|---|
| 1 in | 324 sq ft | Top-up over existing gravel |
| 2 in | 162 sq ft | Garden beds, light paths |
| 3 in | 108 sq ft | Walkways, decorative beds |
| 4 in | 81 sq ft | Driveway surface layer |
| 6 in | 54 sq ft | Driveway base, drainage trench |
| 8 in | 41 sq ft | Heavy-use base over soft ground |
Recommended gravel depth by use
Total compacted depth. A gravel driveway is normally built in two layers — a coarse base and a finer surface — rather than one deep pour.
| Use | Depth | Material |
|---|---|---|
| Garden bed, in place of mulch | 2–3 in | Pea gravel, river rock |
| Walkway or path | 2–3 in | Decomposed granite, pea gravel |
| Patio base under pavers | 4–6 in | Crusher run, compacted |
| Driveway — surface layer | 3–4 in | Crushed stone #57 |
| Driveway — base layer | 4–6 in | Crusher run, compacted |
| French drain / drainage bed | 6–12 in | Crushed stone #57, washed |
Gravel tonnage at a glance
Crushed stone at 100 lb/ft³ including a 10% waste allowance, uncompacted. Use these to sanity-check the calculator.
| Area | At 2 in | At 4 in | At 6 in |
|---|---|---|---|
| 100 sq ft | 0.92 tons | 1.83 tons | 2.75 tons |
| 250 sq ft | 2.29 tons | 4.58 tons | 6.88 tons |
| 500 sq ft | 4.58 tons | 9.17 tons | 13.75 tons |
| 1,000 sq ft | 9.17 tons | 18.33 tons | 27.50 tons |
Values used
Every number this calculator applies on your behalf is listed here, with its source. If your supplier quotes a different figure, use theirs — materials vary by region and grade.
| Value | Used | Typical range | Source |
|---|---|---|---|
| Crushed stone (#57) density | 100 lb/ft³ | 95–105 | USDA Natural Resources Conservation Service |
| Crusher run / dense grade base density | 105 lb/ft³ | 100–115 | USDA Natural Resources Conservation Service |
| Pea gravel density | 105 lb/ft³ | 100–110 | USDA Natural Resources Conservation Service |
| River rock density | 105 lb/ft³ | 98–112 | USDA Natural Resources Conservation Service |
| Decomposed granite density | 110 lb/ft³ | 105–120 | USDA Natural Resources Conservation Service |
| Crushed limestone density | 100 lb/ft³ | 95–110 | USDA Natural Resources Conservation Service |
| Lava rock density | 45 lb/ft³ | 35–55 | USDA Natural Resources Conservation Service |
| Default waste allowance | 10 % | 5–15 | — |
| Cubic yard to ton (crushed stone) | 1.35 | 1.3–1.45 | USDA Natural Resources Conservation Service |
- Crusher run / dense grade base density: Compacts about 22% — order that much extra when it is being rolled.
- Decomposed granite density: Compacts about 18% — order that much extra when it is being rolled.
- Crushed limestone density: Compacts about 20% — order that much extra when it is being rolled.
- Default waste allowance: Covers uneven ground, spreading losses and settlement in the first season.
- Cubic yard to ton (crushed stone): The rule of thumb suppliers quote. It only holds for stone near 100 lb/ft³ — not for lava rock.
Common questions
How much gravel do I need for a driveway?
For a driveway surface, plan on 4 inches of gravel — about 1 cubic yard per 81 square feet, or roughly 1.35 tons of crushed stone per cubic yard. A 30 ft × 12 ft driveway needs about 4.9 cubic yards including waste. If you are building the base as well, add another 4–6 inches of compacted crusher run underneath.
How many cubic yards is a ton of gravel?
About 0.74 cubic yards, because a cubic yard of crushed stone weighs roughly 1.35 tons. That ratio only holds for stone near 100 lb/ft³ — lava rock is closer to 0.6 tons per cubic yard, so the same tonnage covers more than twice the area.
How deep should gravel be?
Two to three inches for a path or garden bed, four to six for a driveway, and six to twelve for a drainage bed. Below about two inches the ground shows through and weeds come up. Above six inches in a single layer, a roller cannot compact the bottom properly, so build it in lifts.
Should I order extra gravel?
Yes — 10% is the standard allowance and this calculator applies it by default. Gravel settles into uneven ground, some is lost in spreading, and the surface drops slightly over the first season. Unlike asphalt, leftover gravel keeps indefinitely, so a small overage costs you nothing.
What is the difference between crushed stone and pea gravel?
Crushed stone is angular, so the pieces lock together and stay where you put them. Pea gravel is rounded, which is comfortable underfoot but migrates under vehicle traffic and needs an edge restraint. For a driveway surface, use crushed stone; for a patio or path where bare feet matter, pea gravel is the nicer surface.
Do I need to order extra for compaction?
Only if the layer is being compacted, which applies to base material rather than decorative gravel. Dense-graded crusher run loses about 20% of its loose volume when rolled, so tick the compaction box and the calculator adds it. Decorative stone is not compacted, so no allowance is needed.
Keep going
Related calculators
- Asphalt calculator
For the paved surface over a gravel base
Guides
- How much gravel do I need?
The cubic-yard shortcut and depth by project type
- Gravel coverage chart
Coverage, weight and depth in one table
- Types of gravel for driveways
Which aggregate belongs in each layer
- Pea gravel vs crushed stone
Which one stays where you put it
- Gravel vs asphalt driveway
Cost over twenty years, not just on day one
Costs
- Gravel driveway cost
Installed prices per square foot and per ton
Sources
- ASTM D448: Standard Sizes of Coarse Aggregate — ASTM InternationalDefines the numbered aggregate sizes (#57, #8, #411) used by US suppliers.
- Engineering Field Handbook — aggregate unit weights — USDA Natural Resources Conservation ServiceLoose and compacted unit weights for common construction aggregates.
- Aggregate Base Course construction guidance — US Federal Highway AdministrationCompaction allowance and layer thickness for aggregate base under paving.
- NIST Special Publication 811: Guide for the Use of the SI — US National Institute of Standards and TechnologyExact definitions of the inch, pound and US short ton used in conversions.
Reviewed by Quban, Construction estimator, on . How these numbers are checked.