Skip to content
No Second Trip

Board Foot Calculator

Hardwood is sold by volume rather than by the piece, and billed on rough thickness: 4/4 is charged as a full inch and delivered at about 13/16 once it is surfaced. That is correct, and it is the thing that catches everyone the first time they buy from a hardwood dealer.

The formulas

Board feet

Board feet = (Thickness in × Width in × Length in) ÷ 144

A board foot is 144 cubic inches — one inch thick by a foot square. If the length is in feet, the equivalent form is thickness × width × length ÷ 12, which is the version most dealers quote.

Nominal thickness

Charged on rough thickness, not surfaced

A 4/4 board is billed as a full inch and arrives at about 13/16 once both faces are dressed. The missing 3/16 became shavings at the mill, and you paid for it — this is standard practice, not a short measure.

What to order

Order = Net board feet × (1 + Waste)

Hardwood arrives in random widths and lengths with defects to cut around, so the board feet that reach the finished piece are well short of the board feet bought. Thirty percent is a normal allowance on FAS and more on the common grades.

Worked example

Six 4/4 boards for a cabinet

Six pieces of 4/4 stock, 8 in wide by 8 ft long. Each is (1 × 8 × 96) ÷ 144 = 5.33 board feet, so the six come to 32 board feet — and 41.6 with the usual 30% hardwood allowance.

41.6 board feet

Four 8/4 legs blanks

Four pieces of 8/4 stock, 6 in wide by 6 ft long, for table legs. Each is (2 × 6 × 72) ÷ 144 = 6 board feet, so 24 in total, or 31.2 with a 30% allowance.

31.2 board feet

Board feet in an 8 ft board

Per board, on nominal thickness. Multiply by the number of pieces.

Thickness4 in wide6 in8 in10 in12 in
4/42.674.005.336.678.00
5/43.335.006.678.3310.00
6/44.006.008.0010.0012.00
8/45.338.0010.6713.3316.00

What each thickness gives you

Surfaced on two faces. You are billed on the rough figure in the first column.

QuotedRoughSurfacedTypical use
4/41 in0.8125 inCabinet and furniture panels, shelving
5/41.25 in1.0625 inStair treads, worktops, heavy shelving
6/41.5 in1.3125 inTable aprons, thick edging
8/42 in1.75 inTable and chair legs, thick tops
10/42.5 in2.25 inHeavy legs and structural furniture parts
12/43 in2.75 inTurning stock, workbench tops
16/44 in3.75 inLarge turnings and timber components

Hardwood grades

Yield is roughly how much of the board comes out as usable clear cuttings — which is why the cheapest grade is not always the cheapest project.

GradeClear yieldTypical wasteBest for
FAS83%20%Firsts and Seconds — the top grade, long clear cuttings
Select83%25%One clear face — good where only one side shows
No. 1 Common66%35%Cabinet grade — shorter clear cuttings, and much cheaper
No. 2 Common50%45%Short cuttings only — economical for small parts and painted work

Values used

Every number this calculator applies on your behalf is listed here, with its source. If your supplier quotes a different figure, use theirs — materials vary by region and grade.

ValueUsedTypical rangeSource
Cubic inches per board foot144 cu in—National Hardwood Lumber Association
4/4 (one inch) surfaced thickness0.81 in—National Hardwood Lumber Association
5/4 surfaced thickness1.06 in—National Hardwood Lumber Association
6/4 surfaced thickness1.31 in—National Hardwood Lumber Association
8/4 (two inch) surfaced thickness1.75 in—National Hardwood Lumber Association
10/4 surfaced thickness2.25 in—National Hardwood Lumber Association
12/4 (three inch) surfaced thickness2.75 in—National Hardwood Lumber Association
16/4 (four inch) surfaced thickness3.75 in—National Hardwood Lumber Association
FAS typical waste20 %—National Hardwood Lumber Association
Select typical waste25 %—National Hardwood Lumber Association
No. 1 Common typical waste35 %—National Hardwood Lumber Association
No. 2 Common typical waste45 %—National Hardwood Lumber Association
Default project waste30 %20–45—
  • Cubic inches per board foot: Exact: one inch thick by twelve inches square.
  • 4/4 (one inch) surfaced thickness: Charged as 1 in rough. Surfacing two faces removes the difference.
  • 5/4 surfaced thickness: Charged as 1.25 in rough. Surfacing two faces removes the difference.
  • 6/4 surfaced thickness: Charged as 1.5 in rough. Surfacing two faces removes the difference.
  • 8/4 (two inch) surfaced thickness: Charged as 2 in rough. Surfacing two faces removes the difference.
  • 10/4 surfaced thickness: Charged as 2.5 in rough. Surfacing two faces removes the difference.
  • 12/4 (three inch) surfaced thickness: Charged as 3 in rough. Surfacing two faces removes the difference.
  • 16/4 (four inch) surfaced thickness: Charged as 4 in rough. Surfacing two faces removes the difference.
  • FAS typical waste: FAS yields roughly 83% clear cuttings.
  • Select typical waste: Select yields roughly 83% clear cuttings.
  • No. 1 Common typical waste: No. 1 Common yields roughly 66% clear cuttings.
  • No. 2 Common typical waste: No. 2 Common yields roughly 50% clear cuttings.
  • Default project waste: Random widths, defect cutting and jointing losses. Not padding.

Common questions

How do you calculate board feet?

Multiply thickness in inches by width in inches by length in inches, then divide by 144. If the length is in feet, divide by 12 instead. A board foot is 144 cubic inches — one inch thick by twelve inches square.

What does 4/4 mean in lumber?

Four quarters of an inch, so nominally one inch thick in the rough. Hardwood thickness is quoted in quarter-inches: 5/4 is an inch and a quarter, 8/4 is two inches. You are billed on that rough figure regardless of how much surfacing removes.

Why is my 4/4 board only 13/16 inches thick?

Because surfacing both faces removes about three sixteenths, and board feet are calculated on the rough thickness you were charged for. This is standard practice throughout the hardwood trade, not a supplier being sharp — buy it rough if you would rather keep the thickness and mill it yourself.

How much waste should I allow for hardwood?

Thirty percent on FAS, and more on the common grades. Boards arrive in random widths that rarely suit your parts, defects have to be cut around, and every jointed edge loses stock. It is a genuine allowance rather than padding.

Is a board foot the same as a linear foot?

No. A linear foot is a length regardless of size; a board foot is a volume. A 1 by 12 board gives one board foot per linear foot, while a 1 by 6 gives half — which is why comparing prices between the two units is meaningless without knowing the dimensions.

Should I buy a cheaper grade to save money?

It depends on the parts. No. 1 Common costs considerably less and yields around two-thirds clear cuttings, which is excellent value for small components. For long clear rails or wide panels the extra waste can easily exceed what the lower grade saved.

Related calculators

Sources

  • Rules for the Measurement and Inspection of Hardwood and Cypress — National Hardwood Lumber AssociationDefines board foot measurement, grading and standard surfaced thicknesses.
  • PS 20: American Softwood Lumber Standard — US Department of Commerce / NISTNominal versus actual dressed sizes for softwood dimensional lumber.
  • Wood Handbook: Wood as an Engineering Material — USDA Forest Products LaboratorySpecies densities, moisture content and dimensional movement.

Reviewed by Quban, Construction estimator, on . How these numbers are checked.