Skip to content
No Second Trip

Guides

How many tons of gravel do I need?

Convert cubic yards to tons for each aggregate type, with the 1.35 rule of thumb, where it breaks down, and how to compare a quote by the ton with one by the yard.

Updated

A tipper truck with its bed raised, tipping a load of crushed stone into a heap on a residential driveway.

The short answer for crushed stone: one cubic yard is about 1.35 tons. Work out the cubic yards, multiply by 1.35, and you have your tonnage.

That rule holds for most driveway aggregate. It falls apart for lightweight decorative stone, which is where people order twice what they need.

Gravel Calculator

Work out how many cubic yards or tons of gravel you need for a driveway, path or drainage bed — with the density for each aggregate type shown in full.

Full gravel calculator, with formulas and sources

Driveway cross-section showing the surface, base and sub-base layersA cut-through view of a driveway. From the top: a three to four inch surface layer of crushed stone, then a four to six inch compacted crusher-run base, then an optional four to eight inch sub-base of larger stone over geotextile fabric, then the subgrade soil.Surface3–4 in crushed stone #57Base4–6 in crusher run, compactedSub-base4–8 in large stone, soft ground onlySubgrade soilGeotextile fabric aboveOrder each layer separatelyDifferent materials, different depths, different densities
A driveway is a layered structure. Most failures are base failures, not surface failures.

The arithmetic, step by step

For a 30 ft × 12 ft driveway at 4 inches:

  1. Area — 30 × 12 = 360 sq ft
  2. Depth in feet — 4 ÷ 12 = 0.333 ft
  3. Volume — 360 × 0.333 = 120 cu ft
  4. Waste — 120 × 1.10 = 132 cu ft
  5. Weight — 132 × 100 lb/ft³ = 13,200 lb
  6. Tons — 13,200 ÷ 2,000 = 6.6 tons

Step 5 is the one that varies. Everything before it is geometry; the density is the material.

Tons per cubic yard, by material

MaterialDensityTons per cu ydSq ft per ton at 4 in
Crushed stone (#57)100 lb/ft³1.3560
Crusher run105 lb/ft³1.4257
Pea gravel105 lb/ft³1.4257
River rock105 lb/ft³1.4257
Decomposed granite110 lb/ft³1.4955
Crushed limestone100 lb/ft³1.3560
Lava rock45 lb/ft³0.61133

Lava rock is the reason to check rather than assume. At 45 lb per cubic foot it is less than half the weight of crushed stone for the same volume — so a tonnage figure calculated with the standard density would have you order more than twice what you need.

Always ask which density your supplier quotes

Aggregate density varies by region, by grade and with moisture. A ten percent difference in density is a ten percent difference in tonnage, which on a six-ton order is most of a short load. If the figure here disagrees with your supplier, use theirs — they are weighing the actual material.

Comparing a quote by the ton against one by the yard

Suppliers split roughly down the middle: landscape yards usually quote cubic yards, quarries and bulk hauliers usually quote tons. Two quotes are not comparable until they are in the same unit.

For crushed stone at 1.35 tons per yard:

Price per tonEquivalent per cubic yard
$30$40.50
$40$54.00
$50$67.50
$60$81.00

Delivery is often the larger variable anyway. It is usually priced per load rather than per ton, so a bigger single order almost always beats two smaller ones — and most trucks cap out somewhere between 10 and 20 tons depending on axle configuration.

Coverage per ton

Useful when a supplier sells only by weight and you are working from an area:

DepthCrushed stoneLava rock
2 in120 sq ft267 sq ft
3 in80 sq ft178 sq ft
4 in60 sq ft133 sq ft
6 in40 sq ft89 sq ft

One thing the tonnage does not include

If the gravel is a compacted base rather than a decorative surface, you are buying loose material that will be rolled down. Dense-graded base loses roughly a fifth of its loose volume when compacted, so the order has to be that much larger than the finished layer. The calculator handles this when you tell it the layer is being compacted.

Related

Common questions

How many tons of gravel are in a cubic yard?

About 1.35 tons for crushed stone at 100 lb per cubic foot. The figure holds for most driveway aggregate, but lava rock is closer to 0.6 tons per yard, so the rule of thumb is worth checking against your material.

How many square feet does a ton of gravel cover?

About 120 square feet at 2 inches deep, 60 at 4 inches and 40 at 6 inches, for crushed stone. Lighter decorative stone covers considerably more, which is why coverage should be worked out from density rather than assumed.

Is gravel cheaper by the ton or by the yard?

Neither inherently — they are the same material measured differently. Convert one to the other before comparing, because a quote of $45 per ton and one of $55 per yard are within a few percent of each other for crushed stone.

How many tons of gravel for a 20x20 driveway?

A 20 by 20 foot area is 400 square feet. At 4 inches deep with a 10 percent allowance that is about 5.4 cubic yards, or roughly 7.3 tons of crushed stone.

Calculators for this

  • Gravel Calculator

    Work out how many cubic yards or tons of gravel you need for a driveway, path or drainage bed — with the density for each aggregate type shown in full.

Part of our driveways guide.

Reviewed by Quban, Construction estimator, on . How these numbers are checked.