Roof Pitch Calculator
Roof pitch is rise over a 12 in run, and almost everything else about a roof follows from it — the angle, the true surface area, the rafter length, and which coverings the code will let you use. Measure it three different ways below.
The formulas
Pitch
Pitch = (Rise ÷ Run) × 12
US roof pitch is always stated over a 12 in run, so any rise-and-run measurement is scaled to that. A rise of 8 in over a 16 in run is 6:12, not 8:16.
Angle and slope
Angle = arctan(Rise ÷ 12) · Slope % = (Rise ÷ 12) × 100
Degrees and percentage are two different things and are often confused. A 12:12 roof is 45 degrees but 100 percent slope — the percentage is rise over run, not a fraction of vertical.
Pitch multiplier
Multiplier = √(Rise² + 12²) ÷ 12
The number that converts a flat footprint into real roof surface. A 6:12 roof has 11.8% more surface than the ground it covers, which is exactly how much extra material you need to buy.
Rafter length
Rafter = Horizontal run × Multiplier
This gives the line length from wall plate to ridge. Add your overhang, and subtract half the ridge board thickness at the top.
Worked example
A standard 6:12 roof
A rise of 6 in over a 12 in run. That is a 26.6° angle, a 50% slope, and a multiplier of 1.1180 — so a 1,500 sq ft footprint has 1,677 sq ft of actual roof, or 16.8 squares of roofing to buy.
6:12
Measured with a level
Holding a 12 in level flat against the slope and measuring 4 in down to the roof surface gives a 4:12 pitch — the shallowest slope that takes standard single-layer underlayment under shingles.
4:12
Roof pitch conversion chart
Every common residential pitch as an angle, a slope percentage and a multiplier. These are generated by the same functions the calculator uses.
| Pitch | Angle | Slope | Multiplier |
|---|---|---|---|
| 1:12 | 4.8° | 8.3% | 1.0035 |
| 2:12 | 9.5° | 16.7% | 1.0138 |
| 3:12 | 14° | 25% | 1.0308 |
| 4:12 | 18.4° | 33.3% | 1.0541 |
| 5:12 | 22.6° | 41.7% | 1.0833 |
| 6:12 | 26.6° | 50% | 1.118 |
| 7:12 | 30.3° | 58.3% | 1.1577 |
| 8:12 | 33.7° | 66.7% | 1.2019 |
| 9:12 | 36.9° | 75% | 1.25 |
| 10:12 | 39.8° | 83.3% | 1.3017 |
| 12:12 | 45° | 100% | 1.4142 |
Minimum roof slope by covering
The lowest slope each material may be installed on. Below 2:12 the choice narrows to membrane and standing-seam systems.
| Covering | Minimum slope | Note |
|---|---|---|
| Asphalt shingles | 2:12 | Doubled underlayment required below 4:12 |
| Wood shakes and shingles | 3:12 | Manufacturer may require more |
| Clay and concrete tile | 2.5:12 | Underlayment requirements increase below 4:12 |
| Standing-seam metal | 3:12 | Sealed seams required at very low slope |
| Corrugated metal panels | 3:12 | Lapped panels need slope to drain |
| Slate | 4:12 | Traditional practice; steeper sheds water better |
| Membrane (EPDM, TPO, PVC) | 3:12 | The only option under 2:12 |
Values used
Every number this calculator applies on your behalf is listed here, with its source. If your supplier quotes a different figure, use theirs — materials vary by region and grade.
| Value | Used | Typical range | Source |
|---|---|---|---|
| Standard run for pitch | 12 in | — | National Roofing Contractors Association |
| Minimum slope for asphalt shingles | 2 | 2–4 | International Code Council |
| Practical walkable limit | 7 | 6–8 | National Roofing Contractors Association |
- Standard run for pitch: US roof pitch is always expressed as rise over a 12 in run. A "6 pitch" means 6 in of rise per 12 in of horizontal travel.
- Minimum slope for asphalt shingles: Permitted from 2:12 with doubled underlayment; standard single underlayment from 4:12 up.
- Practical walkable limit: Above roughly 7:12 most roofers need staging or fall arrest, which increases labour cost.
Common questions
What is a 6:12 roof pitch in degrees?
A 6:12 pitch is 26.6 degrees. The conversion is arctan(6 ÷ 12). The other common ones: 4:12 is 18.4°, 8:12 is 33.7°, and 12:12 is exactly 45°.
How do I measure roof pitch without getting on the roof?
From inside the attic, hold a level horizontally against a rafter, mark 12 inches along it, and measure straight down to the rafter underside. That drop in inches is your pitch. You can also measure the gable end from the ground: the height from the wall top to the ridge is the rise, and half the building width is the run.
What is the minimum roof pitch for shingles?
Two in twelve. From 2:12 to 4:12 the IRC requires two layers of underlayment beneath the shingles, and most manufacturers void their warranty without it. Below 2:12 shingles are not permitted at all — you need a membrane or standing-seam metal roof.
How much bigger is a roof than its footprint?
That is the pitch multiplier. A 4:12 roof is 5.4% larger than the plan area, 6:12 is 11.8% larger, and 12:12 is 41.4% larger. Multiply your footprint by the multiplier to get the true surface area you are buying material for.
What is a roofing square?
One hundred square feet of roof surface. Roofing is quoted, sold and installed by the square, so a 1,677 sq ft roof is about 16.8 squares. Shingles come three bundles to the square for most standard products.
What pitch is too steep to walk on?
Around 7:12 is the practical limit for most roofers in normal footwear. Above that, work needs staging or fall arrest, and labour is usually quoted at a premium — worth knowing when you compare bids on a steep roof.
Keep going
Related calculators
- Soffit calculator
Panels and channel for the eave under this roof
Guides
- How to measure roof pitch
Three methods, including one from inside the attic
- How many shingles do I need?
Footprint to squares to bundles, including waste
- Roof pitch chart
Pitch, angle, slope and multiplier in one table
- Metal roof vs shingles
When the extra cost pays back, and when it does not
Costs
- Roof replacement cost
How pitch and squares drive the price
Sources
- International Residential Code, Section R905: Requirements for Roof Coverings — International Code CouncilMinimum slopes by covering type, and the double-underlayment rule for 2:12 to 4:12 asphalt shingles.
- Residential Asphalt Roofing Manual — Asphalt Roofing Manufacturers AssociationLow-slope application requirements and manufacturer slope limits.
- The NRCA Roofing Manual — National Roofing Contractors AssociationSlope terminology, pitch multipliers and roof area measurement practice.
Reviewed by Quban, Construction estimator, on . How these numbers are checked.